The ventilation aspect of your roof holds quite an importance as far as the overall architecture of the home is concerned. A poorly ventilated home would lead to various associated problems such as moisture molds, leaks and make the entire setup condensed.
Therefore, your attic should be properly ventilated. If you have neglected this aspect during the revamping of your home or roof then a vent can be installed to compensate for the mistake.
The task doesn't necessarily call for the involvement of a professional contractor and can be handled by even a novice. With a right blend of repair tools and supplies, the job can be confined to a two-day task. Make sure that the typical repair tools such as pliers, a hand-held hammer, circular saw, pry bar etc. are at your disposal throughout the course of the project.
The first thing to determine is the location where a vent should be installed. A valuable suggestion can be derived from an expert on that front. Place the pry bar tool under the shingles lying adjacent to the determined area. Make sure that you don't damage the shingles as some of them would be later employed in covering the vent base. Develop a ridge cap by carefully prying up the concerned shingles one by one.
Use a piece of chalk to mark down the area around the ridge cap such that a margin of about 7-8 inches is added on each side of the ridge. Make sure that the chalk is bright enough to notify you about the area later.
Make way for a circular saw and start cutting the shingles from the markings made. Pry up the remains of the shingles with the help of the pry bar tool. Set the sharpness of the blade to a moderate level such that the rafters don't suffer any damage during the operation.
Take a newly purchased vent to the roof carefully and place it in the ridge cap. A baffled vent is often preferred over other vents as it doesn't allow the air to enter into the attic but escapes out the hot air. Cover the setup with the shingles removed and nail them down. Apply some roofing cement to render final touch to the setting.
Make sure that all the safety precautions are followed during the course of the project.
Therefore, your attic should be properly ventilated. If you have neglected this aspect during the revamping of your home or roof then a vent can be installed to compensate for the mistake.
The task doesn't necessarily call for the involvement of a professional contractor and can be handled by even a novice. With a right blend of repair tools and supplies, the job can be confined to a two-day task. Make sure that the typical repair tools such as pliers, a hand-held hammer, circular saw, pry bar etc. are at your disposal throughout the course of the project.
The first thing to determine is the location where a vent should be installed. A valuable suggestion can be derived from an expert on that front. Place the pry bar tool under the shingles lying adjacent to the determined area. Make sure that you don't damage the shingles as some of them would be later employed in covering the vent base. Develop a ridge cap by carefully prying up the concerned shingles one by one.
Use a piece of chalk to mark down the area around the ridge cap such that a margin of about 7-8 inches is added on each side of the ridge. Make sure that the chalk is bright enough to notify you about the area later.
Make way for a circular saw and start cutting the shingles from the markings made. Pry up the remains of the shingles with the help of the pry bar tool. Set the sharpness of the blade to a moderate level such that the rafters don't suffer any damage during the operation.
Take a newly purchased vent to the roof carefully and place it in the ridge cap. A baffled vent is often preferred over other vents as it doesn't allow the air to enter into the attic but escapes out the hot air. Cover the setup with the shingles removed and nail them down. Apply some roofing cement to render final touch to the setting.
Make sure that all the safety precautions are followed during the course of the project.
About the Author:
Scott Rodgers is a renowned writer who has been authoring on roofing contents for a long time now. His expertise and guidance has given motivation to a host of workers, ranging from Springtown Roofers to Poquoson Roofers.
0 comments:
Post a Comment